DComTalk.com

Guest

Hello all,

I've an AS5300 with 8 Channelized E1/PRI ports (Quad Cards With 4
Serial Interfaces) using the following firmwares :
- c5300-is-mz.122-2.XA.bin
- mica-modem-pw.2.9.4.0.bin

I wonder if I can configure the E1 controller as unframed E1
"channel-group 0 unframed " because I tried to do it and It says: "%
Invalid input detected at '^' marker."

Does the firmware and the E1/PRI Card support that ? if the problem is
any or both firmware version, which one should be used. if it's the
E1/PRI card doesn't support it which card is the adequate solution

Thanks a Lot

Following the version on the AS5300:
nas-AS5300# sh ver
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-IS-M), Version 12.2(2)XA, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC:Home:SW:IOS:Specials for info
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 27-Jun-01 01:27 by hwcheng
Image text-base: 0x600089B0, data-base: 0x61034000

ROM: System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
BOOTFLASH: 5300 Software (C5300-BOOT-M), Version 12.0(4)T1, RELEASE
SOFTWARE (fc1)

nas-AS5300 uptime is 1 week, 3 days, 9 hours, 55 minutes
System returned to ROM by reload at 00:11:02 UTC Sat Jan 1 2000
System image file is "flash:c5300-is-mz.122-2.XA.bin"

cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes
of memory.
Processor board ID 24709928
R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Backplane revision 2
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 3.2, Item Number 800-2544-04,
Board Revision B0, Serial Number 24709928,
PLD/ISP Version 0.0, Manufacture Date 25-Feb-2001.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
9 Serial network interface(s)
120 terminal line(s)
8 Channelized E1/PRI port(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)

Aaron Leonard · Guest

Nope, the channelized E1s on the AS5xxx platforms do not support
unframed operation. Only up to a 30*64=1920kbps channel-group.

Aaron

---

~ Hello all,
~
~ I've an AS5300 with 8 Channelized E1/PRI ports (Quad Cards With 4
~ Serial Interfaces) using the following firmwares :
~ - c5300-is-mz.122-2.XA.bin
~ - mica-modem-pw.2.9.4.0.bin
~
~ I wonder if I can configure the E1 controller as unframed E1
~ "channel-group 0 unframed " because I tried to do it and It says: "%
~ Invalid input detected at '^' marker."
~
~ Does the firmware and the E1/PRI Card support that ? if the problem is
~ any or both firmware version, which one should be used. if it's the
~ E1/PRI card doesn't support it which card is the adequate solution
~
~ Thanks a Lot
~
~ Following the version on the AS5300:
~ nas-AS5300# sh ver
~ Cisco Internetwork Operating System Software
~ IOS (tm) 5300 Software (C5300-IS-M), Version 12.2(2)XA, EARLY
~ DEPLOYMENT RELEASE SOFTWARE (fc1)
~ TAC:Home:SW:IOS:Specials for info
~ Copyright (c) 1986-2001 by cisco Systems, Inc.
~ Compiled Wed 27-Jun-01 01:27 by hwcheng
~ Image text-base: 0x600089B0, data-base: 0x61034000
~
~ ROM: System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE
~ SOFTWARE (fc1)
~ BOOTFLASH: 5300 Software (C5300-BOOT-M), Version 12.0(4)T1, RELEASE
~ SOFTWARE (fc1)
~
~ nas-AS5300 uptime is 1 week, 3 days, 9 hours, 55 minutes
~ System returned to ROM by reload at 00:11:02 UTC Sat Jan 1 2000
~ System image file is "flash:c5300-is-mz.122-2.XA.bin"
~
~ cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes
~ of memory.
~ Processor board ID 24709928
~ R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache
~ Channelized E1, Version 1.0.
~ Bridging software.
~ X.25 software, Version 3.0.0.
~ SuperLAT software (copyright 1990 by Meridian Technology Corp).
~ Primary Rate ISDN software, Version 1.1.
~ Backplane revision 2
~ Manufacture Cookie Info:
~ EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
~ Board Hardware Version 3.2, Item Number 800-2544-04,
~ Board Revision B0, Serial Number 24709928,
~ PLD/ISP Version 0.0, Manufacture Date 25-Feb-2001.
~ 1 Ethernet/IEEE 802.3 interface(s)
~ 1 FastEthernet/IEEE 802.3 interface(s)
~ 9 Serial network interface(s)
~ 120 terminal line(s)
~ 8 Channelized E1/PRI port(s)
~ 128K bytes of non-volatile configuration memory.
~ 16384K bytes of processor board System flash (Read/Write)
~ 8192K bytes of processor board Boot flash (Read/Write)

matrixdz2002 · Guest

Thanks Aron for your answer,

Could you please tell me which E1 Card should I use with the AS5300 to
can apply unframed E1, because I read on some cisco web pages some
configurations where the AS 5300 is used with E1 unframed.

Which is the reference of the adequate Card , it's importante to me
because the company has only the AS5300 and are connected to the
backbone using 2048 Kb.

Thanks a lot

Aaron Leonard · Guest

On 4 Dec 2005 00:29:00 -0800, "matrixdz2002" <matrixdz2002@yahoo.fr> wrote:

~ Thanks Aron for your answer,
~
~ Could you please tell me which E1 Card should I use with the AS5300 to
~ can apply unframed E1, because I read on some cisco web pages some
~ configurations where the AS 5300 is used with E1 unframed.
~
~ Which is the reference of the adequate Card , it's importante to me
~ because the company has only the AS5300 and are connected to the
~ backbone using 2048 Kb.
~
~ Thanks a lot

In order to run unframed 2048Kbps E1 into an AS5300, you would have to use
one of the following cards:

AS53-4CE1+
AS53-8CE1+

The "+" indicates that, in addition to the 4 or 8 channelized E1 ports,
the card also has 4 high speed (up to 8Mbps) serial ports.
http://www.cisco.com/en/US/products/hw/univgate/ps501/products_installation_guide_chapter09186a008007de67.html

Then you would need to connect an external CSU/DSU that supports 2048Kbps
unframed E1 to one of these serial ports.

Cheers,

Aaron

	DComTalk.com Forum Index -> Cisco	All times are GMT
Page 1 of 1