| Author |
Message |
wonga316
Guest
|
 Posted:
Tue Aug 30, 2005 7:38 am Post subject:
ITG Card and Static Routes |
|
|
hi,
does anyone know if it's possible to add and activate two static routes
on an ITG card? one for ELAN and the other TLAN.
at the moment, the only active route i have in the route net table is
for the TLAN. it looks like -
destination | gateway
0.0.0.0 | <TLAN gateway addr>
it's taken from the ITG shell. from OTM the GW settings for the ELAN
and TLAN are different.
thx, wonga316 |
|
| Back to top |
|
 |
Pennyman
Guest
|
| Posted:
Wed Aug 31, 2005 2:48 am Post subject:
Re: ITG Card and Static Routes |
|
|
Yes it is possible,
You can create a gateway for the elan during installation.
Its in the same commandline when you give the ITG-card its ip-adres for the
Elan.
For t-lan you can define a gateway with OTM or in the command line
interface.
Give ? for all possible commands,
There is one command like set route or something like that.
Pennyman,
"wonga316" <wonga316@yahoo.com.au> schreef in bericht
news:1125369517.691225.307530@g44g2000cwa.googlegroups.com...
| Quote: | hi,
does anyone know if it's possible to add and activate two static routes
on an ITG card? one for ELAN and the other TLAN.
at the moment, the only active route i have in the route net table is
for the TLAN. it looks like -
destination | gateway
0.0.0.0 | <TLAN gateway addr
it's taken from the ITG shell. from OTM the GW settings for the ELAN
and TLAN are different.
thx, wonga316
|
|
|
| Back to top |
|
|
Ray
Guest
|
| Posted:
Wed Aug 31, 2005 4:42 am Post subject:
Re: ITG Card and Static Routes |
|
|
wonga316 wrote:
| Quote: | hi,
does anyone know if it's possible to add and activate two static routes
on an ITG card? one for ELAN and the other TLAN.
at the moment, the only active route i have in the route net table is
for the TLAN. it looks like -
destination | gateway
0.0.0.0 | <TLAN gateway addr
it's taken from the ITG shell. from OTM the GW settings for the ELAN
and TLAN are different.
thx, wonga316
|
Yes,
Via OTM or the card CLI. I seem to remember (been a while since I touched
an ITG!!) that routes are flushed on a card reboot - worth checking |
|
| Back to top |
|
|
wonga316
Guest
|
| Posted:
Wed Aug 31, 2005 8:22 am Post subject:
Re: ITG Card and Static Routes |
|
|
thanks guys. I found the commands 'routeAdd' and 'mRouteAdd'. i also
found a in otm tab called snmp traps / routing and ips. it's the card
routing table entries section.
Ray wrote:
| Quote: | wonga316 wrote:
hi,
does anyone know if it's possible to add and activate two static routes
on an ITG card? one for ELAN and the other TLAN.
at the moment, the only active route i have in the route net table is
for the TLAN. it looks like -
destination | gateway
0.0.0.0 | <TLAN gateway addr
it's taken from the ITG shell. from OTM the GW settings for the ELAN
and TLAN are different.
thx, wonga316
Yes,
Via OTM or the card CLI. I seem to remember (been a while since I touched
an ITG!!) that routes are flushed on a card reboot - worth checking |
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in