| Author |
Message |
Tech Geek
Guest
|
 Posted:
Mon Aug 08, 2005 4:20 pm Post subject:
Multiple T1 transmissions on Cat5E |
|
|
My question is regarding the transmission of multiple T1 signals on
Category-5E cables bundled together. The reason I have this question is
one of my data center customers decided to extend (48) T1 lines from
the Telco room to IVR equipment over (48) Cat5E cables. Then terminate
on standard 48-port RJ-45 patch panel. The intent is to run each T1 on
an individual Cat5E cable (ie. Tx & Rx within each cable). My cusomter
claims that there would be no intereference between all these T1 lines
running together in the cable tray. The distance is over 100 feet.
Normally, the way I design T1 cable runs is to either use 56-pair ABAM
and terminate on a DSX panel; or substitute the ABAM with Category-3
and terminate each Cat-3 bundle one for Tx and one for Rx.
I was taught by an SBC engineer once that running more than 6-7 T1s in
individual Category-5E/6 cables next to each other will cause
interference or cross-talk. Is this true from your knowledge and
experience?? |
|
| Back to top |
|
 |
Robert Redelmeier
Guest
|
| Posted:
Mon Aug 08, 2005 4:20 pm Post subject:
Re: Multiple T1 transmissions on Cat5E |
|
|
Tech Geek <oelissa@yahoo.com> wrote:
| Quote: | each T1 on an individual Cat5E cable (ie. Tx & Rx within
each cable). My cusomter claims that there would be no
intereference between all these T1 lines running together
in the cable tray. The distance is over 100 feet.
|
I don' t have direct experience with that many T1s, but I
wouldn't expect any problems over such a short distance in
such tightly twisted wire. There's a lot of power (current)
in a T1, but twist tames power.
| Quote: | I was taught by an SBC engineer once that running more
than 6-7 T1s in individual Category-5E/6 cables next to
each other will cause interference or cross-talk. Is this
true from your knowledge and experience??
|
What I've heard is there is a limit to the number of T1
that will run cleanly per cable binder-group (25pr). 1 is
fine. 2-3 usually work. 6+ is trouble. This depends on wire
guage, twist (Cat1 - 3) and cable feet.
-- Robert |
|
| Back to top |
|
|
James Knott
Guest
|
| Posted:
Tue Aug 09, 2005 12:20 am Post subject:
Re: Multiple T1 transmissions on Cat5E |
|
|
glen herrmannsfeldt wrote:
| Quote: | Since T1 can normally be run over pairs of a 25 pair cable where
the possible coupling should be much higher than adjacent Cat5
cables, I wouldn't expect much of a problem.
Both inductive and capacitive coupling between twisted pairs increase
with frequency, and T1 runs at much lower frequencies than ethernet.
That isn't a guarantee, but it is an indication that the problem
should be much less than for ethernet.
|
The concern is near end cross talk, where the transmitter interferes with
the receiver. Using separate cables or individually shielded pairs fixes
that problem. |
|
| Back to top |
|
|
glen herrmannsfeldt
Guest
|
| Posted:
Tue Aug 09, 2005 12:20 am Post subject:
Re: Multiple T1 transmissions on Cat5E |
|
|
Tech Geek wrote:
| Quote: | My question is regarding the transmission of multiple T1 signals on
Category-5E cables bundled together. The reason I have this question is
one of my data center customers decided to extend (48) T1 lines from
the Telco room to IVR equipment over (48) Cat5E cables. Then terminate
on standard 48-port RJ-45 patch panel. The intent is to run each T1 on
an individual Cat5E cable (ie. Tx & Rx within each cable). My cusomter
claims that there would be no intereference between all these T1 lines
running together in the cable tray. The distance is over 100 feet.
Normally, the way I design T1 cable runs is to either use 56-pair ABAM
and terminate on a DSX panel; or substitute the ABAM with Category-3
and terminate each Cat-3 bundle one for Tx and one for Rx.
I was taught by an SBC engineer once that running more than 6-7 T1s in
individual Category-5E/6 cables next to each other will cause
interference or cross-talk. Is this true from your knowledge and
experience??
|
Since T1 can normally be run over pairs of a 25 pair cable where
the possible coupling should be much higher than adjacent Cat5
cables, I wouldn't expect much of a problem.
Both inductive and capacitive coupling between twisted pairs increase
with frequency, and T1 runs at much lower frequencies than ethernet.
That isn't a guarantee, but it is an indication that the problem
should be much less than for ethernet.
-- glen |
|
| Back to top |
|
|
I am a Sock Puppet
Guest
|
| Posted:
Tue Aug 09, 2005 12:20 am Post subject:
Re: Multiple T1 transmissions on Cat5E |
|
|
Tech Geek wrote:
| Quote: | My question is regarding the transmission of multiple T1 signals on
Category-5E cables bundled together. The reason I have this question is
one of my data center customers decided to extend (48) T1 lines from
the Telco room to IVR equipment over (48) Cat5E cables. Then terminate
on standard 48-port RJ-45 patch panel. The intent is to run each T1 on
an individual Cat5E cable (ie. Tx & Rx within each cable). My cusomter
claims that there would be no intereference between all these T1 lines
running together in the cable tray. The distance is over 100 feet.
Normally, the way I design T1 cable runs is to either use 56-pair ABAM
and terminate on a DSX panel; or substitute the ABAM with Category-3
and terminate each Cat-3 bundle one for Tx and one for Rx.
I was taught by an SBC engineer once that running more than 6-7 T1s in
individual Category-5E/6 cables next to each other will cause
interference or cross-talk. Is this true from your knowledge and
experience??
|
I routinely get away with running two T1's on one 4 pair cat5 cable,
distance of about 75 feet. I got 11 T1's total, over six cat5e cables,
all in the same cable tray, all bundled together with tie wraps.
No issues. Works fine.
Your mileage may vary.
--
DO NOT REPLY TO THE EMAIL ADDRESS
IN THE HEADERS OF THIS POST.
IT IS A SPAM TRAP ADDRESS. |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in