| Author |
Message |
Lonnie
Guest
|
 Posted:
Fri Sep 24, 2004 6:30 pm Post subject:
isdn debug output |
|
|
I have been having consistent problems with my ISDN line from Verizon.
It is a standard BRI. I am over 18000 ft from the CO, so they
installed a repeater outside my house. The ISDN line will come up but
I get alot of debug messages and the line goes down. L1 actually shows
deactivated. It keeps going up and down, they verizon techs are
clueless and have sitched pairs, installed new cards, etc.. Sometimes
it works for a few weeks, then its up and down again. I am interested
in an explanation of the following debug outputs.
Aug 5 02:33:55.891: BRI1: Recvd MPH_EI2_IND from L1
Aug 5 02:33:55.891: BRI1: L1 ERR IF_ACTIVE
I have also included the config and a complete section of debug
output.
Current configuration : 1465 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Cisco804
!
boot system flash c800-y6-mw.122-3.bin
logging buffered 8192 debugging
enable secret 5 xxxxxxx
!
username xxxxx password 7 xxxxx
!
dial-peer voice 1 pots
caller-id
call-waiting
ring 0
registered-caller ring 1
port 1
destination-pattern 1234567
!
dial-peer voice 2 pots
caller-id
call-waiting
ring 0
registered-caller ring 1
port 212345678719825
!
pots country US
ip subnet-zero
no ip source-route
!
isdn switch-type basic-ni
!
!
!
interface Ethernet0
ip address 209.150.xxx.xx 255.255.255.248
ip access-group 121 in
no ip proxy-arp
!
interface BRI0
ip unnumbered Ethernet0
encapsulation ppp
dialer string 1234567890
dialer-group 1
isdn switch-type basic-ni
isdn spid1 12345678900101 4567890
isdn spid2 12345678900101 4567890
isdn incoming-voice modem
isdn T310 5000
compress predictor
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 7 xxxxx
ppp pap sent-username xxxxx password xxxxx
ppp multilink
!
no ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 BRI0
!
!
map-class dialer DialClasas
dialer-list 1 protocol ip permit
!
line con 0
exec-timeout 120 0
stopbits 1
line vty 0 4
exec-timeout 0 0
login local
!
!
time-range TIME
periodic daily 0:00 to 23:59
!
end
******************************************************************
debug isdn events
debug isdn q921
debug isdn q931
*****************************************************************
02:34:26: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:34:26: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:34:35: ISDN BR0: TX -> RRp sapi = 0 tei = 65 nr = 3
02:34:35: ISDN BR0: RX <- RRf sapi = 0 tei = 65 nr = 1
02:34:56: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:34:56: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:35:4295008256: ISDN BR0: L1 ERR IF_ACTIVE
02:35:05: ISDN BR0: TX -> RRp sapi = 0 tei = 65 nr = 3
02:35:05: ISDN BR0: RX <- RRf sapi = 0 tei = 65 nr = 1
02:35:26: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:35:26: ISDN BR0: RX <- RRp sapi = 0 tei = 112 nr = 3
02:35:26: ISDN BR0: TX -> RRf sapi = 0 tei = 112 nr = 5
02:35:26: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:35:35: ISDN BR0: TX -> RRp sapi = 0 tei = 65 nr = 3
02:35:35: ISDN BR0: RX <- RRf sapi = 0 tei = 65 nr = 1
02:35:56: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:35:56: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:36:05: ISDN BR0: TX -> RRp sapi = 0 tei = 65 nr = 3
02:36:05: ISDN BR0: RX <- RRf sapi = 0 tei = 65 nr = 1
02:36:26: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:36:26: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:36:35: ISDN BR0: TX -> RRp sapi = 0 tei = 65 nr = 3
02:36:35: ISDN BR0: RX <- RRp sapi = 0 tei = 65 nr = 1
02:36:35: ISDN BR0: TX -> RRf sapi = 0 tei = 65 nr = 3
02:36:35: ISDN BR0: RX <- RRf sapi = 0 tei = 65 nr = 1
02:36:163208798208: ISDN BR0: L1 ERR IF_ACTIVE
02:36:56: ISDN BR0: TX -> RRp sapi = 0 tei = 112 nr = 5
02:36:56: ISDN BR0: RX <- RRf sapi = 0 tei = 112 nr = 3
02:37:17179910144: ISDN BR0: Recvd MPH_EI2_IND from L1
02:37:17179869184: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected
from
44336
86161 00d0.5203.6c2d, call lasted 248 seconds
02:37:17179869184: ISDN: get_isdn_service_state(): idb 0x27B81BC bchan
2
is_isdn
1 Not a Pri
02:37:17179869184: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old
State = 4
02:37:17187277832: %LINK-3-UPDOWN: Interface BRI0:1, changed state to
down
02:37:21474836480: ISDN BR0: Physical layer is IF_DOWN
02:37:05: ISDN BR0: Shutting down ME
02:37:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 112
changed to
dow
n
02:37:05: ISDN BR0: L2-TERM: ces/tei=1/112 INIT->TERM_DOWN
02:37:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BRI0, TEI 65
changed to
down
02:37:05: ISDN BR0: Shutting down ISDN Layer 3
02:37:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 112
changed to
down
02:37:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 65
changed to down
02:37:05: ISDN BR0: Incoming call id = 0x0114, dsl 0
02:37:05: ISDN BR0: L2-TERM: ces/tei=1/0 TERM_DOWN->AWAIT_ESTABLISH
02:37:05: ISDN BR0: Incoming call id = 0x0115, dsl 0
02:37:05: ISDN BR0: L2-TERM: ces/tei=2/0 INIT->AWAIT_ESTABLISH
02:37:05: ISDN BR0: Activating
02:37:05: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:05: ISDN BR0: Could not bring up interface
02:37:05: ISDN BR0: Shutting down ISDN Layer 3
02:37:05: ISDN BR0: Activating
02:37:05: ISDN BR0: Outgoing call id = 0x80D5, dsl 0
02:37:05: ISDN BR0: Could not bring up interface
02:37:05: ISDN BR0: Shutting down ISDN Layer 3
02:37:21541949352: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:21482246132: ISDN BR0: process_bri_call(): call id 0x80D5,
called_number
4
433686161, speed 64, call type DATA
02:37:05: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:05: 1 0 1 80 D5 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:05:
02:37:05: CC_CHAN_GetIdleChanbri: dsl 0
02:37:05: Found idle channel B1
02:37:05: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
changed state
to down
02:37:25771393700: ISDN BR0: L1 persistent Deactivated
02:37:07: ISDN BR0: Outgoing call id = 0x80D6, dsl 0
02:37:30131883944: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:30072180724: ISDN BR0: process_bri_call(): call id 0x80D6,
called_number
4
433686161, speed 64, call type DATA
02:37:07: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:07: 1 0 1 80 D6 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:07:
02:37:07: CC_CHAN_GetIdleChanbri: dsl 0
02:37:07: Found idle channel B2
02:37:07: ISDN BR0: Activating
02:37:07: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:07: ISDN BR0: Could not bring up interface
02:37:07: ISDN BR0: Shutting down ISDN Layer 3
02:37:07: ISDN BR0: Activating
02:37:08: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
02:37:08: ISDN BR0: Physical layer is IF_DOWN
02:37:08: ISDN BR0: Could not bring up interface
02:37:08: ISDN BR0: Shutting down ISDN Layer 3
02:37:08: ISDN BR0: Shutting down ME
02:37:08: ISDN BR0: Shutting down ISDN Layer 3
02:37:08: ISDN BR0: Outgoing call id = 0x80D7, dsl 0
02:37:34359738368: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:34367148020: ISDN BR0: process_bri_call(): call id 0x80D7,
called_number
4
433686161, speed 64, call type DATA
02:37:08: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:08: 1 0 1 80 D7 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:08:
02:37:08: CC_CHAN_GetIdleChanbri: dsl 0
02:37:08: Found idle channel B1
02:37:08: ISDN BR0: Activating
02:37:08: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:09: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
02:37:09: ISDN BR0: Physical layer is IF_DOWN
02:37:09: ISDN BR0: Could not bring up interface
02:37:09: ISDN BR0: Shutting down ISDN Layer 3
02:37:09: ISDN BR0: Shutting down ME
02:37:09: ISDN BR0: Shutting down ISDN Layer 3
02:37:10: ISDN BR0: Outgoing call id = 0x80D8, dsl 0
02:37:42949672960: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:42957082612: ISDN BR0: process_bri_call(): call id 0x80D8,
called_number
4
433686161, speed 64, call type DATA
02:37:10: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:10: 1 0 1 80 D8 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:10:
02:37:10: CC_CHAN_GetIdleChanbri: dsl 0
02:37:10: Found idle channel B1
02:37:10: ISDN BR0: Activating
02:37:10: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:11: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
02:37:11: ISDN BR0: Physical layer is IF_DOWN
02:37:11: ISDN BR0: Could not bring up interface
02:37:11: ISDN BR0: Shutting down ISDN Layer 3
02:37:11: ISDN BR0: Shutting down ME
02:37:11: ISDN BR0: Shutting down ISDN Layer 3
02:37:11: ISDN BR0: Outgoing call id = 0x80D9, dsl 0
02:37:47244640256: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:47252049908: ISDN BR0: process_bri_call(): call id 0x80D9,
called_number
4
433686161, speed 64, call type DATA
02:37:11: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:11: 1 0 1 80 D9 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:11:
02:37:11: CC_CHAN_GetIdleChanbri: dsl 0
02:37:11: Found idle channel B1
02:37:11: ISDN BR0: Activating
02:37:11: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:12: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
02:37:12: ISDN BR0: Physical layer is IF_DOWN
02:37:12: ISDN BR0: Could not bring up interface
02:37:12: ISDN BR0: Shutting down ISDN Layer 3
02:37:12: ISDN BR0: Shutting down ME
02:37:12: ISDN BR0: Shutting down ISDN Layer 3
02:37:13: ISDN BR0: Outgoing call id = 0x80DA, dsl 0
02:37:55834574848: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:55841984500: ISDN BR0: process_bri_call(): call id 0x80DA,
called_number
4
433686161, speed 64, call type DATA
02:37:13: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:13: 1 0 1 80 DA 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:13:
02:37:13: CC_CHAN_GetIdleChanbri: dsl 0
02:37:13: Found idle channel B1
02:37:13: ISDN BR0: Activating
02:37:13: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:60129542144: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old
State = 4
02:37:60129542144: ISDN BR0: Physical layer is IF_DOWN
02:37:14: ISDN BR0: Shutting down ME
02:37:14: ISDN BR0: Shutting down ISDN Layer 3
02:37:14: ISDN BR0: Could not bring up interface
02:37:14: ISDN BR0: Shutting down ISDN Layer 3
02:37:14: ISDN BR0: Outgoing call id = 0x80DB, dsl 0
--More--
02:37:13: CC_CHAN_GetIdleChanbri: dsl 0
02:37:13: Found idle channel B1
02:37:13: ISDN BR0: Activating
02:37:13: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:60129542144: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old
State = 4
02:37:60129542144: ISDN BR0: Physical layer is IF_DOWN
02:37:14: ISDN BR0: Shutting down ME
02:37:14: ISDN BR0: Shutting down ISDN Layer 3
02:37:14: ISDN BR0: Could not bring up interface
02:37:14: ISDN BR0: Shutting down ISDN Layer 3
02:37:14: ISDN BR0: Outgoing call id = 0x80DB, dsl 0
02:37:60196655016: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:60136951796: ISDN BR0: process_bri_call(): call id 0x80DB,
called_number
4
433686161, speed 64, call type DATA
02:37:14: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:14: 1 0 1 80 DB 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:14:
02:37:14: CC_CHAN_GetIdleChanbri: dsl 0
02:37:14: Found idle channel B1
02:37:14: ISDN BR0: Activating
02:37:14: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
02:37:15: ISDN BR0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
02:37:15: ISDN BR0: Physical layer is IF_DOWN
02:37:15: ISDN BR0: Could not bring up interface
02:37:15: ISDN BR0: Shutting down ISDN Layer 3
02:37:15: ISDN BR0: Shutting down ME
02:37:15: ISDN BR0: Shutting down ISDN Layer 3
02:37:98785837732: ISDN BR0: L1 is IF_ACTIVE
02:37:98784248474: ISDN BR0 EVENT: isdn_sw_cstate: State = 4, Old
State = 4
02:37:98791657116: ISDN BR0: L2-TERM: ces/tei=1/0
AWAIT_ESTABLISH->TERM_DOWN
02:37:98784288768: ISDN BR0: L2-TERM: ces/tei=2/0
AWAIT_ESTABLISH->TERM_DOWN
02:37:98791656980: ISDN BR0: Incoming call id = 0x0116, dsl 0
02:37:98784247808: ISDN BR0: L2-TERM: ces/tei=1/0
TERM_DOWN->AWAIT_ESTABLISH
02:37:23: ISDN BR0: TX -> IDREQ ri = 22626 ai = 127
02:37:25: ISDN BR0: TX -> IDREQ ri = 56963 ai = 127
02:37:27: ISDN BR0: TX -> IDREQ ri = 50868 ai = 127
02:37:124554051584: ISDN BR0: L1 ERR IF_ACTIVE
02:37:29: ISDN BR0: Incoming call id = 0x0117, dsl 0
02:37:29: ISDN BR0: LIF_EVENT: ces/callid 1/0x0 HOST_DISCONNECT_ACK
02:37:29: ISDN BR0: Error: Unfound B-channel on Disconnect_Ack -
callid 0x0
02:37:29: ISDN BR0: TX -> IDREQ ri = 12789 ai = 127
02:37:128849059840: ISDN BR0: L1 ERR IF_ACTIVE
02:37:31: ISDN BR0: TX -> IDREQ ri = 20806 ai = 127
02:37:33: ISDN BR0: TX -> IDREQ ri = 26023 ai = 127
02:37:33: ISDN BR0: RX <- IDASSN ri = 26023 ai = 72
02:37:33: ISDN BR0: TX -> SABMEp c/r = 0 sapi = 0 tei = 72
02:37:33: ISDN BR0: RX <- UAf c/r = 0 sapi = 0 tei = 72
02:37:33: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 72 changed
to up
02:37:33: ISDN BR0: L2-TERM: ces/tei=1/72 AWAIT_ESTABLISH->ESTABLISHED
02:37:33: ISDN BR0: L2-TERM: ces/tei=1/72 ESTABLISHED->AWAIT_INIT
02:37:33: ISDN BR0: TX -> INFOc sapi = 0 tei = 72 ns = 0 nr = 0 i
=
0x08007
B3A0E3431303837313938323430313031
02:37:33: INFORMATION pd = 8 callref = (null)
SPID Information i = '41087198240101'
02:37:33: ISDN BR0: RX <- RRr sapi = 0 tei = 72 nr = 1
02:37:33: ISDN BR0: RX <- INFOc sapi = 0 tei = 72 ns = 0 nr = 1 i
=
0x08007
B3B028081
02:37:33: INFORMATION pd = 8 callref = (null)
ENDPOINT IDent i = 0x8081
02:37:33: ISDN BR0: TX -> RRr sapi = 0 tei = 72 nr = 1
02:37:33: CCBRI_Go Fr L3 pkt (Len=7) :
02:37:33: 7B 0 93 3B 2 80 81
02:37:33:
02:37:33: ISDN BR0: L2-TERM: ces/tei=1/72 usid/tid=0/1
AWAIT_INIT->INIT
02:37:33: ISDN BR0: Received EndPoint ID
02:37:33: ISDN BR0: Incoming call id = 0x0118, dsl 0
02:37:33: ISDN BR0: L2-TERM: ces/tei=2/0 TERM_DOWN->AWAIT_ESTABLISH
02:37:33: ISDN BR0: RX <- INFOc sapi = 0 tei = 72 ns = 1 nr = 1 i
=
0x08007
B952A0480800150
02:37:33: INFORMATION pd = 8 callref = (null)
Locking Shift to Codeset 5
02:37:33: Codeset 5 IE 0x2A i = 0x808001, 'P'
02:37:33: ISDN BR0: TX -> RRr sapi = 0 tei = 72 nr = 2
02:37:33: CCBRI_Go Fr L3 pkt (Len=10) :
02:37:33: 7B 0 93 95 2A 4 80 80 1 50
02:37:33:
02:37:33: ISDN BR0: TX -> IDREQ ri = 49176 ai = 127
02:37:33: ISDN BR0: RX <- IDASSN ri = 49176 ai = 81
02:37:33: ISDN BR0: TX -> SABMEp c/r = 0 sapi = 0 tei = 81
02:37:33: ISDN BR0: RX <- UAf c/r = 0 sapi = 0 tei = 81
02:37:33: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 81 changed
to up
02:37:33: ISDN BR0: L2-TERM: ces/tei=2/81 AWAIT_ESTABLISH->ESTABLISHED
02:37:33: ISDN BR0: L2-TERM: ces/tei=2/81 ESTABLISHED->AWAIT_INIT
02:37:33: ISDN BR0: TX -> INFOc sapi = 0 tei = 81 ns = 0 nr = 0 i
=
0x08007
B3A0E3431303837313938323530313031
02:37:33: INFORMATION pd = 8 callref = (null)
SPID Information i = '41087198250101'
02:37:33: ISDN BR0: RX <- RRr sapi = 0 tei = 81 nr = 1
02:37:33: ISDN BR0: RX <- INFOc sapi = 0 tei = 81 ns = 0 nr = 1 i
=
0x08007
B3B028181
02:37:33: INFORMATION pd = 8 callref = (null)
ENDPOINT IDent i = 0x8181
02:37:34: ISDN BR0: TX -> RRr sapi = 0 tei = 81 nr = 1
02:37:34: CCBRI_Go Fr L3 pkt (Len=7) :
02:37:34: 7B 0 93 3B 2 81 81
02:37:34:
02:37:34: ISDN BR0: L2-TERM: ces/tei=2/81 usid/tid=1/1
AWAIT_INIT->INIT
02:37:34: ISDN BR0: Received EndPoint ID
02:37:34: ISDN BR0: RX <- INFOc sapi = 0 tei = 81 ns = 1 nr = 1 i
=
0x08007
B952A0480800150
02:37:34: INFORMATION pd = 8 callref = (null)
Locking Shift to Codeset 5
02:37:34: Codeset 5 IE 0x2A i = 0x808001, 'P'
02:37:34: ISDN BR0: TX -> RRr sapi = 0 tei = 81 nr = 2
02:37:34: CCBRI_Go Fr L3 pkt (Len=10) :
02:37:34: 7B 0 93 95 2A 4 80 80 1 50
02:37:34:
02:37:45: ISDN BR0: Outgoing call id = 0x80DC, dsl 0
02:37:193340641192: ISDN BR0: Event: Call to 4433686161 at 64 Kb/s
02:37:193280937972: ISDN BR0: process_bri_call(): call id 0x80DC,
called_number
4433686161, speed 64, call type DATA
02:37:45: CCBRI_Go Fr Host InPkgInfo (Len=25) :
02:37:45: 1 0 1 80 DC 0 4 2 88 90 18 1 83 2C A 34 34 33 33 36 38 36 31
36 31
02:37:45:
02:37:45: CC_CHAN_GetIdleChanbri: dsl 0
02:37:45: Found idle channel B1
02:37:45: ISDN BR0: TX -> INFOc sapi = 0 tei = 72 ns = 1 nr = 2 i
=
0x08014
305040288901801832C0A34343333363836313631
02:37:45: SETUP pd = 8 callref = 0x43
02:37:45: Bearer Capability i = 0x8890
02:37:45: Channel ID i = 0x83
02:37:45: Keypad Facility i = '4433686161'
02:37:45: ISDN BR0: RX <- RRr sapi = 0 tei = 72 nr = 2
02:37:46: ISDN BR0: RX <- INFOc sapi = 0 tei = 72 ns = 2 nr = 2 i
=
0x0801C
302180189
02:37:46: CALL_PROC pd = 8 callref = 0xC3
02:37:46: Channel ID i = 0x89
02:37:46: ISDN BR0: TX -> RRr sapi = 0 tei = 72 nr = 3
02:37:46: CCBRI_Go Fr L3 pkt (Len=7) :
02:37:46: 2 1 43 98 18 1 89
02:37:46:
02:37:46: ISDN BR0: LIF_EVENT: ces/callid 1/0x80DC HOST_PROCEEDING
02:37:46: ISDN BR0: HOST_PROCEEDING
02:37:46: ISDN BR0: HOST_MORE_INFO
02:37:46: ISDN BR0: RX <- INFOc sapi = 0 tei = 72 ns = 3 nr = 2 i
=
0x0801C
301340101
02:37:46: ALERTING pd = 8 callref = 0xC3
02:37:46: Signal i = 0x01 - Ring back tone on
02:37:46: ISDN BR0: TX -> RRr sapi = 0 tei = 72 nr = 4
02:37:46: CCBRI_Go Fr L3 pkt (Len=7) :
02:37:46: 1 1 43 94 34 1 1
02:37:46:
02:37:46: ISDN BR0: LIF_EVENT: ces/callid 1/0x80DC HOST_ALERTING
02:37:46: ISDN BR0: RX <- INFOc sapi = 0 tei = 72 ns = 4 nr = 2 i
=
0x0801C
30734013F
02:37:46: CONNECT pd = 8 callref = 0xC3
02:37:46: Signal i = 0x3F - Tones off
02:37:46: ISDN BR0: TX -> RRr sapi = 0 tei = 72 nr = 5
02:37:46: CCBRI_Go Fr L3 pkt (Len=7) :
02:37:46: 7 1 43 91 34 1 3F
02:37:46:
02:37:46: ISDN BR0: LIF_EVENT: ces/callid 1/0x80DC HOST_CONNECT
02:37:46: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
02:37:46: ISDN: get_isdn_service_state(): idb 0x27B81BC bchan 2
is_isdn 1 Not a
Pri
02:37:46: ISDN BR0: Event: Connected to 4433686161 on B1 at 64 Kb/s
02:37:197570085540: ISDN BR0: L1 ERR IF_ACTIVE
02:37:46: ISDN BR0: TX -> INFOc sapi = 0 tei = 72 ns = 2 nr = 5 i
=
0x08014
30F
02:37:46: CONNECT_ACK pd = 8 callref = 0x43
02:37:47: ISDN BR0: RX <- RRr sapi = 0 tei = 72 nr = 3
02:37:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
changed state
to up
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:219043373056: ISDN BR0: L1 ERR IF_ACTIVE
02:37:223338340352: ISDN BR0: L1 ERR IF_ACTIVE
02:37:52: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to
4433686161
00d0.
5203.6c2d
*****************************************************************************
This output is a sample of what I am seeing when the line goes down
until it comes back up.
Any help would be greatly appreciated, I am running out of options and
would like to be able to point the verizon engineers in the right
direction. Please e-mail me at lonniempaschall@yahoo.com |
|
| Back to top |
|
 |
Loren Amelang
Guest
|
| Posted:
Fri Sep 24, 2004 10:17 pm Post subject:
Re: isdn debug output |
|
|
On 24 Sep 2004 07:30:03 -0700, lonniempaschall@yahoo.com (Lonnie)
wrote:
| Quote: | I have been having consistent problems with my ISDN line from Verizon.
It is a standard BRI. I am over 18000 ft from the CO, so they
installed a repeater outside my house. The ISDN line will come up but
I get alot of debug messages and the line goes down. L1 actually shows
deactivated. It keeps going up and down, they verizon techs are
clueless and have sitched pairs, installed new cards, etc.. Sometimes
it works for a few weeks, then its up and down again.
|
Hi,
Not sure I'm any help here, but it looks like your connection
regularly shuts down Layer 2 as well as Layer 3. I've never seen that
on my SBC line, and I'm 36 miles from my CO.
My 804 sometimes has problems getting Layer 2 up if it has been
disconnected or the power to the repeater has been out. If I don't see
"MULTIPLE_FRAME_ESTABLISHED" in the status, it isn't going to work, no
matter how long I wait. I have to keep unplugging the cable or cycling
power until the status comes up correctly. Then my Layer 2 stays up
for weeks or months on the same TEI, until there is some power glitch.
I can't imagine how much hassle I would have if Layer 2 dropped after
every call!
The other thing I've seen here is that if the backup batteries in the
repeater hut are bad, almost every AC power failure will destroy my
line card. It will test good, and sometimes will synch up, but there
will be lots of data errors until they swap it out.
Loren
Cisco804#show isdn status
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 82, Ces = 1, SAPI = 0, State =
MULTIPLE_FRAME_ESTABLISHED
TEI = 83, Ces = 2, SAPI = 0, State =
MULTIPLE_FRAME_ESTABLISHED
Spid Status:
TEI 82, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 70, tid = 1
TEI 83, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 71, tid = 1
BTW - How do you get HH:MM:SS times in your log? Mine shows either a
big decimal number value, or a hex value... |
|
| Back to top |
|
|
Lonnie
Guest
|
| Posted:
Tue Sep 28, 2004 5:49 pm Post subject:
Re: isdn debug output |
|
|
Thanks for your input Loren. To get the time in you log you need to
add the following commands to your config
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
Lonnie
Loren Amelang <loren@pacific.net> wrote in message news:<j9o8l0lae2kgp3tq1ppg66446kcn1etg3a@4ax.com>...
| Quote: | On 24 Sep 2004 07:30:03 -0700, lonniempaschall@yahoo.com (Lonnie)
wrote:
I have been having consistent problems with my ISDN line from Verizon.
It is a standard BRI. I am over 18000 ft from the CO, so they
installed a repeater outside my house. The ISDN line will come up but
I get alot of debug messages and the line goes down. L1 actually shows
deactivated. It keeps going up and down, they verizon techs are
clueless and have sitched pairs, installed new cards, etc.. Sometimes
it works for a few weeks, then its up and down again.
Hi,
Not sure I'm any help here, but it looks like your connection
regularly shuts down Layer 2 as well as Layer 3. I've never seen that
on my SBC line, and I'm 36 miles from my CO.
My 804 sometimes has problems getting Layer 2 up if it has been
disconnected or the power to the repeater has been out. If I don't see
"MULTIPLE_FRAME_ESTABLISHED" in the status, it isn't going to work, no
matter how long I wait. I have to keep unplugging the cable or cycling
power until the status comes up correctly. Then my Layer 2 stays up
for weeks or months on the same TEI, until there is some power glitch.
I can't imagine how much hassle I would have if Layer 2 dropped after
every call!
The other thing I've seen here is that if the backup batteries in the
repeater hut are bad, almost every AC power failure will destroy my
line card. It will test good, and sometimes will synch up, but there
will be lots of data errors until they swap it out.
Loren
Cisco804#show isdn status
Global ISDN Switchtype = basic-ni
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 82, Ces = 1, SAPI = 0, State =
MULTIPLE_FRAME_ESTABLISHED
TEI = 83, Ces = 2, SAPI = 0, State =
MULTIPLE_FRAME_ESTABLISHED
Spid Status:
TEI 82, ces = 1, state = 5(init)
spid1 configured, spid1 sent, spid1 valid
Endpoint ID Info: epsf = 0, usid = 70, tid = 1
TEI 83, ces = 2, state = 5(init)
spid2 configured, spid2 sent, spid2 valid
Endpoint ID Info: epsf = 0, usid = 71, tid = 1
BTW - How do you get HH:MM:SS times in your log? Mine shows either a
big decimal number value, or a hex value... |
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in